How To Set A Schlage Keypad Lock

The Kwikset Kevo is i of the most pop smart locks on the market, but if you're a stickler for keypads, the Schlage Connect is an option to consider. Here'south how to install and set up the Schlage Connect smart lock.

RELATED: Are Smart Locks Secure?

The Connect isn't an addition to your existing deadbolt, simply rather a full replacement. This can brand the installation process a bit daunting for those who've never replaced a lock before. So before you get started, make certain that this is something you're comfy doing. If non, it may be wise to call a knowledgeable friend (or a professional person locksmith) to help.

This guide also assumes that you already accept a deadbolt installed on your door. If you don't, and so you'll need to drill a completely new hole in your door to install the Kevo (or whatsoever deadbolt for that matter) using ane of these.

Luckily, the Schlage Connect comes with everything that yous'll need, just you lot'll need a couple of tools to put it all together: a screwdriver or ability drill, and perhaps a hammer. If you do decide to use a power drill, exist actress careful not to over-tighten any screws.

Pace One: Remove Your Existing Deadbolt

Outset by removing the deadbolt that's currently installed on your door, which usually involves removing a couple of screws from the inside. My deadbolt is of the battery-powered keypad variety, and so it's a bit more complex to remove. If you just have a uncomplicated deadbolt, this process should exist a lot easier for y'all.

Later those screws are removed, carefully accept off the encompass. You may have to slightly tap on information technology with a hammer to loosen it upwards if information technology doesn't come off easily.

There will exist two more screws on the inside that yous'll demand to remove. These connect the within portion of the lock to the outside portion.

Once those screws are removed, you tin can carefully pull apart the unabridged lock and remove it, starting with the interior department.

From there, remove the outside portion.

Adjacent, remove the two screws on the latch.

Pull the latch out of the door.

You lot at present have a clean slate to install the Schlage Connect smart lock.

Step Two: Install the Schlage Connect

The first step is to install the latch. Depending on the mortise of your door, there are different faceplates you can use, including a square faceplate, a rounded faceplate, and i without a faceplate at all. Have a look at your previous door latch and match it with the new 1 to see which one you need to apply.

Insert the door latch into the door. Make sure that the middle hole in the door latch is centered inside the door's hole. If not, remove the latch, hold onto the deadbolt latch and rotate the mechanism 180 degrees to alter the position of the middle hole. Re-insert the latch, making sure the "TOP" marking on the latch is facing upward.

Adjacent, detect the screws that have unlike threading (there will exist four of them included, merely yous only need two).

Utilize these ii screws to secure the door latch onto the door.

Adjacent, slide the keypad portion of the lock onto the outside office of the door.

Brand certain that the cablevision feeds through the door hole and that the sticking out lines up and slides into the center pigsty of the door latch.

So take the support plate and identify it on the within office of the door, making certain that the side that reads "Against Door" is placed…well…confronting the door. When you practise this, feed the cable through from the other side and line up the bolt holes.

Adjacent, take the two long bolts included with the lock (the non-pointy ones) and screw the back up plate into place.

Afterward that, grab the inside associates and remove the battery encompass.

At this point, yous'll as well want to jot down the "Programming Code" and "User Codes" that are printed on the back of the assembly. You tin can change these in the future, but you'll need them initially afterwards installing the lock.

After you write those down, hold the assembly upwards to the lock and plug the cable into the back of it.

Route the cablevision into the grooves.

Slide the associates over the back up plate, making sure that the table sticking through lines up with the knob and push it all the way on.

Take the long black commodities and secure the inside assembly to the back up plate.

And so take the really tiny spiral and secure the upper portion.

Once that's consummate, remove the battery tray by sliding it up and out of the assembly.

Insert the four AA batteries that came included with the lock.

Slide the battery tray dorsum into the assembly and connect the bombardment connector to the battery tray.

After that, place the battery cover back on.

Adjacent, it'south time to test out the lock and see if it works. Start by opening up the door (keeping it unlocked) and press on the "Schlage" button at the tiptop of the keypad. The keypad should light up.

From in that location, enter in 1 of the user codes. If successful, the deadbolt will extend and retract. The lock should now be set to go for manual usage.

Step Three: Connect It to Your Smarthome Hub

While you can perform all sorts of functions on the lock itself (like adding new codes, changing codes, etc.), the big kicker for this lock is the ability to control and manage it from your smartphone by connecting it to a Z-Wave smarthome hub.

RELATED: SmartThings vs. Wink vs. Insteon: Which Smarthome Hub Should Yous Purchase?

How y'all do this is completely dependent on what type of smarthome hub you have, but the process should exist mostly the same all around. In my case, I'm going to connect the lock to my Wink hub.

To do this, you lot'll first need to open your smarthome hub app and navigate to where you add a device to the hub to put information technology in search mode.

Next, open your door, extend the deadbolt out then that it'due south in the locked position, and so press the Schlage button followed by your programming code plus "0". The orange dot volition blink and afterward a few seconds the green check mark should light up, which indicates that connection was successful.

Once the lock has connected to the smarthome hub, you can begin controlling it from the hub's app and practise things similar lock and unlock remotely, change user codes, and more.

Once again, you can ever manage the lock's functionality using the lock itself without the need to connect it to a smarthome hub, merely with the Schlage Connect, you're substantially paying for the smarthome capabilities, so it would exist beneficial to have advantage of information technology.

Source: https://www.howtogeek.com/330039/how-to-install-and-set-up-the-schlage-connect-smart-lock/

Share this post